Motor oil additive for restoring engine performance characteristics: compression, power, acceleration, effective fuel consumption, as well as for extending the wear life and protection in emergency situations. Compound is designed for the treatment of diesel engines of passenger cars with a mileage less than 50,000 kilometres. Suitable for all engine types and designs, including turbocharged and non-turbocharged.
Tribotechnical compound does not react with motor oils and their packages of chemical additives, does not change their properties and characteristics. According to the method of use, the composition can be called "engine additive".

EFFECTS OF APPLICATION

Under the influence of tribo-compound, a protective metal layer is formed on the worn parts, which is able to hold the engine oil film more firmly.

This allows you to solve the following tasks

RESTORE AND EQUALIZE THE COMPRESSION IN THE CYLINDERS

Partial restoring of the shape of the cylinders and a dense oil film on their surface seal the gaps in the cylinder-piston group between the compression rings and the cylinder walls, which provide the necessary gas density.

This prevents the gases from escaping, and consequently restores compression and aligns it with the cylinders. Treatment with tribo-compound can not increase the compression above the nominal provided for this particular engine, which makes the use of the composition safe.

REDUCE THE CONSUMPTION OF OIL BURNING

If the oil consumption is due to other reasons: "hardened" oil seals or destruction of oil-removing caps, tribo-compound will not be able to solve this problem.

The protective layer restores the shape of the surface of the plunger of the hydraulic compensator, optimizes the gaps, which prevents oil breakout and normalizes its pressure.

This ensures high-quality and silent operation of the mechanism.

Restoring and equalizing the compression on the cylinders leads to smooth operation of the engine.
In addition, a thick layer of oil softens the pistons. All this reduces vibration and noise in the engine.

The drop in oil pressure is due to increased gaps in the friction pairs of the CPG (Cylinder Piston Group), as well as due to wear of the pump.
Restoring of the friction surfaces leads to the optimization of gaps. In this case, the oil pump raises the output pressure to the nominal, reducing pressure losses due to expanded gaps in the CPG, in the block head, in the crank mechanism.

Restoring and equalization of compression provides a more complete combustion of fuel, reducing losses when gases break through.

The dense oil film expands the hydrodynamic friction zone, which reduces friction losses. While maintaining the driving mode, this reduces fuel consumption by 6-8% for vehicles with high mileage. In new cars, it allows you to avoid increasing fuel consumption by significantly slowing down the wear process.

Increase engine power and acceleration

Restoring and equalization of compression provides a more complete combustion of fuel, reducing losses when gases break through.

The dense oil film expands the hydrodynamic friction zone, which reduces friction losses. Together, this leads to an increase in the power received from the fuel unit and an improvement in the dynamic characteristics of the engine.

Get rid of the smoke from the exhaust, reduce its toxicity

Recovery of compression and optimization of gaps in the cylinder-piston group ensure high-quality fuel combustion and reduce oil fumes.

This reduces the content of unburned fuel particles and oil combustion products in the exhaust gases, which reduces their smoke and toxicity.

In addition to the solution of actual problems, the use of additive allows you to achieve preventive effects

Make it easier to start the engine and reduce its wear during "cold start"

The drop in oil pressure is due to increased gaps in the friction pairs of the CPG, as well as due to wear of the pump.

The restoration of the friction surfaces leads to the optimization of gaps. In this case, the oil pump raises the output pressure to the nominal, reducing pressure losses due to expanded gaps in the CPG, in the block head, in the crank mechanism

Extend the life (resource) of the engine

Due to its structural features, the protective layer has increased microelasticity (it is deformed in a collision and then restores its shape, instead of being destroyed) and microhardness (it is not destroyed when loads from wear particles occur).

A denser oil film on the surface of the layer also reduces the direct contact of parts, withstands increased thermal and mechanical loads.

All this helps reduce engine wear, especially during long periods of downtime in traffic jams, when the oil is overheated and liquefied, when maneuvering at low speeds or their sharp set, when oil starvation occurs.

Protect the engine from wear at high loads

Due to its structural features, the protective layer has increased microelasticity (it is deformed in a collision and then restores its shape, instead of being destroyed) and microhardness (it is not destroyed when loads from wear particles occur).

A denser oil film on the surface of the layer also reduces the direct contact of parts, withstands increased thermal and mechanical loads.

All this allows you to reduce engine wear, especially during long downtime in traffic jams,when the oil is overheated and liquefied, when maneuvering at low speeds or their sharp set, when oil starvation occurs.

To protect the engine in case of an emergency loss of oil

The oil film, held on the protective layer due to its structural features, is able to protect the engine from scuffing and jamming in the event of a sudden drop in oil pressure.

This allows you to avoid breakage if the oil loss or pressure drop was not noticed immediately. In addition, in some cases (depending on the design of the specific engine), this allows you to gently drive the car to the service station on your own.

Reduce the consumption of oil burning

The protective layer restores the density of the sleeve – ring – piston groove.
This improves oil removal from the cylinder walls and reduces its fumes in the combustion chamber, especially at high engine speeds.
If the oil consumption is due to other reasons: "hardened" oil seals or destruction of oil-removing caps, tribo-compound will not be able to solve this problem.

SIGNS OF ENGINE WEAR

There are various signs that the wear of engine components is approaching critical. As a rule, increasing wear is characterized by a decrease in engine dynamics, an increase in average fuel consumption in the same driving modes.

The following are some of the most common signs of wear and tear, in which the treatment of the engine with tribo-compound can significantly delay the need for repair:

There was a sound of "iron clang" when starting the engine

Due to wear of the cylinder walls, the gaps between them and the piston rings widen.

When starting the engine, when it is cold and the gaps have not yet decreased due to the thermal expansion of the parts, the piston can make transverse movements accompanied by a shock. The rapid succession of blows merges into a General "ringing", the engine "rattles".

This is especially noticeable when starting in the cold, when the gaps are expanded even more. This indicates that the cylinder surfaces are very worn, and each such launch wears them even more.

There was a constant blue smoke in the exhaust

Blue smoke means that oil is constantly entering the combustion chambers, which indicates that there are widened gaps in the cylinder-piston group due to wear of the cylinder walls and piston rings.

Tribotechnical compound is able to restore worn surfaces, remove smoke and oil consumption. If the blue smoke appears only when starting the engine, and then disappears, you need to check the oil caps. Most likely, during downtime, oil flows through them and accumulates in the combustion chambers. In this case, the tribo-compound will not help, since the oil-removing caps are made of rubber.

Engine started to work louder, harder, and there was a vibration

These signs may indicate that the compression balance is disturbed.

Pistons in different cylinders are pushed with different forces, which disrupts the uniformity of the engine. If this sign appeared suddenly and sharply drew attention to itself, it is possible that there was a failure – for example, a piston ring burst. If the vibration and noise increased gradually, imperceptibly, then most likely this is the result of wear of the CPG, in this case, the tribotechnical compound will be able to restore the worn surfaces and get rid of signs of wear.

There was a "clatter" of hydraulic compensators at the time of engine warming up

The chattering sound when the engine is running "cold" indicates that the hydraulic compensators can not hold the oil pressure due to wear on the plunger surface.
During engine operation, they heat up, heat gaps disappear, and pressure loss does not occur so quickly. However, the "clatter" that appears indicates that further wear of the plungers will only increase and will lead to the need to replace the hydraulic compensators. Treating the engine with tribo-compound can help solve this problem without disassembling the engine.

APPLICATION

Oil additive "Active Diesel” is designed to restore performance and protect against wear of diesel engines of passenger cars with a mileage of more than 50,000 kilometres. It can be used for accelerated and turbocharged engines.

Tribotechnical Compound Atomium Active Gasoline New is designed for application on gasoline engines and LPG engines (including alusil and nikasil coating) of passenger vehicles and light trucks with mileage less than 50 000 km, including condition after overhaul.

Effects of application

• Improves the process of engine burnishing, including condition after overhaul (because of the adaptive properties of the LC, that work on optimization of conjugated friction parts)
  
• Increases of the engine life in 1.5 - 2 times (due to wear intensity decreasing)
  
• Increases engine effective power (as a result of fuel combustion quality improvement, decreasing combustion gas leakages to carter, and drop of friction losses)
  
• Provides maximum engine protection in extreme working conditions, also in case of overloading or overheating and during «cold start-up»
  
• Makes start at low temperatures much easier
  
• Does not degrade the operational characteristics of rubber parts
  
• Decreases fuel consumption of internal combustion engine to 6 - 8 % (as a result of compression recovering and combustion quality improvement)
  
• Decreases noise and vibration levels by 5 - 10 dB (due to forming of thick and resistant lubrication “pillow” and clearances optimization)
  
• Decreases exhaust CO/CH emissions up to 50 % (as a result of improvement of combustion quality)
  
• Decreases oil waste
  
• Provides the possibility of short-time run under oil starvation conditions or when oil (oil pressure) is completely lost
  

Application mode

• Before applying Atomium Active Gasoline New shake the can thoroughly until natural sediments (active components) are totally dissolved
  
• Apply Atomium Active Gasoline New through the regular oil filling neck of the warmed-up engine
  
• After applying Atomium Active Gasoline New the engine should work on single turns (at idle) for 5 min. and then run for no less than 20 min. in any mode (regular operation)
  
• It is not recommended to apply the lubricant at the existence of mechanical breakages of parts and assemblies
  
• Atomium Active Gasoline New is compatible with any type of motor oils and doesn't change its properties
  
• For providing a continuous level of engine protection it is recommended to apply Atomium Active Regular at 30 000 - 40 000 km after the complete treatment with Atomium Active
  
• After 100 000 km to repeat the treatment with Atomium Active Gasoline Plus is recommended
  
• For turbocharged engines and forced engines the re-treatment is recommended after 50 000-55 000 km
  
• To achieve the full level of protection the treatment of all vehicle parts is recommended, such as transmission gears, hydraulic power steering, etc.
  

Features

• In case of contact with skin remove the material wash out with warm water, and then wash again with soap
  
• In case of contact with eyes wash out eyes with a large amount of water
  
• In case of swallowing consult a doctor

The 1st stage: Add Lubricant Composition Atomium Active Gasoline New to the working engine oil through the oil filling neck (see the graph for calculation), then run the car till the next regular oil replacement (but no less than 1000 km). In case of significant oil contamination (identity by the color of the oil on the dipstick or oil spots on filter paper) start the second stage of treatment immediately.

Recommendations (after the 1st stage): Change the engine oil; Replace oil and air filter.

The 2nd stage: Add Atomium Active Gasoline New to the new engine oil (see the graph), and then run the car in a regular mode till the next oil replacement.

Precautions: Not harmful if applied correctly.

Tribotechnical Compound Atomium Active Gasoline Plus is designed for application on gasoline engines and LPG engines (including alusil and nikasil coating) of passenger vehicles and light trucks with mileage more than 50 000 km 
EFFECTS OF APPLICATION

• Cleans friction surfaces from lacquers and deposits on the 1st stage of treatment, including de-coking of the piston rings in their mobility;

• Increases and stabilizes compression in the ICE cylinders (due to the formation of a new layer and sealing gaps in friction units);

• Restores oil pressure in the engine oil system up to rated;

• Decreases oil waste;

• Increases of the engine life in 1.5-2 times (due to wear intensity decreasing);

• Increases engine effective power (as a result of fuel combustion quality improvement, decreasing combustion gas leakages to carter, and drop of friction losses);

• Reduces oil waste consumption in the engine up to 3 times (due to the increase in gas-tight piston grooves);

• Provides maximum engine protection in extreme working conditions, also in case of overloading or overheating and during «cold start-up»;

• Makes start at low temperatures much easier;

• Does not degrade operational characteristics of rubber parts;

• Decreases fuel consumption of internal combustion engine to 8-10 % (as a result of compression recovering and combustion quality improvement);

• Decreases noise and vibration levels by 5-10 dB (due to forming of thick and resistant lubrication “pillow” and clearances optimization);

• Decreases exhaust CO/CH emissions up to 50 % (as a result of improvement of combustion quality);.

• Provides the possibility of short-time run under oil starvation conditions or when oil (oil pressure) is completely lost;

• . Restores the work of hydro-compensators (tappets).

• Before applying Atomium Active Gasoline Plus shake the can thoroughly until natural sediments (active components) are totally dissolved.

• Apply Atomium Active Gasoline Plus through the regular oil filling neck of the warmed-up engine.

• After applying Atomium Active Gasoline Plus the engine should work on single turns (at idle) for 5 min. and then run for no less than 20 min. in any mode (regular operation).

• At mileage, more than 80 000 km use our long-term Atomium Active Gasoline Plus during the 1st stage200 km before the oil change.

• It is not recommended to apply the Lubricant at the existence of mechanical breakages of parts and assemblies.

• Atomium Active Gasoline Plus is compatible to any type of engine oils and doesn't change its properties.

• For providing a continuous level of engine protection it is recommended to apply Atomium Active Regular 30 000 - 40 000 km after complete treatment with Atomium Active Gasoline Plus.

• After 100 000 km re-treatment is recommended.

• For turbocharged engines and forced engines, re-treatment is recommended after 50 000-55 000 km.

• To achieve the full level of protection the treatment of all vehicle parts is recommended, such as transmission gears, hydraulic power steering, etc.

• In case of contact with skin remove the material wash out with warm water, and then wash again with soap.

• In case of contact with eyes wash out eyes with a large amount of water.

• In case of swallowing consult a doctor

 The 1st stage: Add Lubricant Composition Atomium  Active Gasoline Plus to the engine oil 500-1000 km before oil replacement, pour through the oil filling neck (see the graph for calculation), then run the car till the next regular oil replacement (but no less than 500 km). In case of significant oil contamination (identity by the color of the oil on the dipstick or oil spots on filter paper) start the second stage of treatment immediately.

Recommendations (after the 1st Stage): Change oil; Replace oil and air filter.

The 2nd stage: Add Atomium Active Gasoline Plus to the new engine oil (see the graph), and then run the car in a regular mode till the next oil replacement.

The 3rd stage: Add Atomium Active Gasoline Plus to the new engine oil (see the graph), and then run the car in a regular mode till the next oil replacement.

Important:

Precautions: Not harmful if applied correctly.

Engine oil additive for restoring engine performance characteristics: compression, power, acceleration, effective fuel consumption, as well as for extending the wear life and protection in emergency situations. It will get rid of oil extra usage and engine smoke. The compound is designed for the treatment of gasoline and gas engines (LPG, CNG) of passenger cars with a mileage less than 50,000 kilometres. Suitable for all engine types and designs, including turbocharged and non-turbocharged.

EFFECTS OF APPLICATION

Under the influence of tribo-compound, a protective metal layer is formed on the worn parts, which is able to hold the engine oil film more firmly.

This allows you to solve the following tasks

EXTEND THE LIFE RESOURCE OF THE ENGINE

Due to its structural features, the protective layer has increased microelasticity (it is deformed in a collision and then restores its shape, instead of being destroyed) and microhardness (it is not destroyed when loads from wear particles occur).

A denser oil film on the surface of the layer also reduces the direct contact of parts, withstands increased thermal and mechanical loads.

All this allows you to reduce engine wear, especially during long downtime in traffic jams, when the oil is overheated and liquefied, when maneuvering at low speeds or their sharp set, when oil starvation occurs.

MAKE IT EASIER TO START THE ENGINE AND REDUCE ITS WEAR DURING "COLD START"

Treated surfaces are able to retain the oil film during prolonged downtime. This makes it easier to perform the first turns and prevents increased engine wear during oil starvation at the start-up, which is especially important at a negative ambient temperature.

PROTECT THE ENGINE FROM WEAR DURING HIGH LOADS AND ACTIVE DRIVING

Due to its structural features, the protective layer has increased microelasticity (it is deformed in a collision and then restores its shape, instead of being destroyed) and microhardness (it is not destroyed when loads from wear particles occur).

A denser oil film on the surface of the layer also reduces the direct contact of parts, withstands increased thermal and mechanical loads.

All this allows you to reduce engine wear, especially during long downtime in traffic jams,when the oil is overheated and liquefied, when maneuvering at low speeds or their sharp set, when oil starvation occurs.

PROTECT THE ENGINE IN CASE OF AN EMERGENCY LOSS OF OIL

The oil film, held on the protective layer due to its structural features, is able to protect the engine from scuffing and jamming in the event of a sudden drop in oil pressure.

This allows you to avoid breakage if the oil loss or pressure drop was not noticed immediately. In addition, in some cases (depending on the design of the specific engine), this allows you to gently drive the car to the service station on your own.

PREVENT OIL CONSUMPTION FROM FUMES

The protective layer restores the density of the sleeve – ring – piston groove Assembly. This improves oil removal from the cylinder walls and reduces its fumes in the combustion chamber, especially at high engine speeds.

If the oil consumption is due to other reasons: "hardened" oil seals or destruction of oil-removing caps, tribo-compound will not be able to solve this problem.

MAINTAIN THE NOMINAL FUEL CONSUMPTION

Restoring and equalization of compression provides a more complete combustion of fuel, reducing losses when gases break through.

The dense oil film expands the hydrodynamic friction zone, which reduces friction losses. While maintaining the driving mode, this reduces fuel consumption by 6-8% for vehicles with high mileage. In new cars, it allows you to avoid increasing fuel consumption by significantly slowing down the wear process.

REDUCE NOISE AND VIBRATION WHEN THE ENGINE IS RUNNING

The protective layer speeds up and facilitates the work-in of parts. The new engine optimizes friction gaps faster, reduces the number of contacts on the surface of parts, normalizes compression, and the engine runs evenly and smoothly. This reduces noise and vibration when the engine is running.

HOW TO USE IT

Full treatment will require two bottles of the composition. It is added to the oil filler neck. It does not require any special knowledge or tools.

Adding the compound to the engine oil can be performed by any car owner on any passenger car independently. However, it is important to pay attention to the instructions attached to each bottle of the compound, so that it works as effectively as possible.

The standard treatment procedure is following:

•  A bottle of the compound is added to the oil about 1000 kilometres before the planned regular oil change.
•  Another bottle of the compound is added after replacement to the fresh oil and works there throughout the entire inter-service run.

HOW IT WORKS

Under the influence of tribocompound, a protective metal layer is formed on the friction surfaces of parts, which is able to hold the engine oil film more firmly. This layer significantly reduces the wear rate of parts even under high loads and oil starvation, which allows you to maintain the engine's rated characteristics for 70.000 – 90.000 kilometres of mileage.

Tribotechnical compound contains particles of the active mineral. When they fall into the zones of local contact surfaces, where there is a high local pressure, and the temperature exceeds 1000 C – mineral particles change the flow of friction processes. The surface of the part is able to "capture" metal microparticles that are in the lubricant. Gradually, a solid metal protective layer is formed on the entire worn surface, which is characterized by a porous structure with a large number of micro-depressions. The particles of the mineral itself remain in the oil and continue to have the necessary effects on other areas.

The micropores of the protective layer are filled with oil, which forms a continuous film on it due to surface tension forces. This oil film is never completely separated from the surface of the part, does not run off, even with a long idle time. The protective layer itself can withstand heavy loads due to increased microhardness and microelasticity compared to the original factory surface.

Restoring the shape and more effective lubrication, allow the parts to perform their functions as it was laid down in the engine design, which leads to the restoration of the performance characteristics of all friction units.

APPLICATION

Oil additive "Active Gasoline New” is designed to restore performance and protect against wear of gasoline, LPG, CNG engines of passenger cars with a mileage less than 50,000 kilometres. It can be used for accelerated and turbocharged engines.

Treatment of the engine with tribotechnical compound "Active" is performed in two stages. At each stage it is necessary to add the compound to the engine oil according to the following procedure:

1. Warm up the engine to operating temperature (normal operation).
2. Turn off the engine.
3. Carefully mix the contents of the bottle so that the sediment at the bottom is distributed throughout the entire volume of the liquid.
4. Pour 1 bottle of the compound into the oil filler neck of the engine. (If the volume of the oil system is more than 5 litres, it is necessary to fill two bottles of the composition).
5. Immediately after adding the compound, make a trip by car for 20-25 minutes in normal operation.
6. After the application of the compound, the car can be used as usual.

Complete treatment of the engine is performed according to the following scheme:

* If the mileage before the regular oil change is more than 1000 km, it is necessary to conduct a drip oil test every 500-1000 km. If the oil has become densely black, it is necessary to make its early replacement and go to the second stage.

Recommendations: 

• To maintain engine performance we recommend to use multi-function cleaning additive to the gasoline fuel SUPROTEC "SGA (SGA)";
•  To restore the transmission resource, it is recommended to use tribotechnical compound "MGSB", "AGSB", "REDUCER»;
•  To restore the characteristics of the power steering system, we recommend the compound "HPS".

Atomium compound creates special conditions in areas of friction which leads to building up a protective metal layer. It covers worn surfaces, optimizes friction clearances, and retains dense oil film.

THIS ALLOWS YOU TO SOLVE THE FOLLOWING TASKS:

Restoration of the cylinders’ shape and a dense oil film on their surface seal the gaps between the compression rings and the cylinder walls. This prevents the breakthrough of gases and as the result increases compression and levels it among cylinders. Treatment with tribo-compound can not make the compression higher than the nominal level defined for this specific engine which makes the use of the composition safe.
Restoration of worn cylinders and piston rings is in fact the only stable and safe way to improve the tightness of their mating. It makes Atomium compound one of the best additives for low compression cases.

Treatment with the Atomium compound improves the mobility of piston rings (by cleaning up piston grooves) and narrows friction clearances between them and cylinders. This makes ring work more efficient and improves oil removal from the cylinder walls. Less oil gets into the combustion chamber and burns out there, especially at high engine speeds. Restoration of worn surfaces is a kind of “natural” way to fix oil burning root cause. There are additives for engine burning oil which are focused exactly on this problem. The Atomium compound proposes a decrease in oil consumption just as one positive effect in the row of others.

Remember – there might be other reasons for oil burning, for example - "hardened" valve stem seals. The most noticeable symptom of it is bluish smoke in the exhaust after an idle period. The tribotechnical compound is inactive with rubber details and unable to restore their functionality. 
The level of motor oil may also constantly go down in case of oil leakage. The most often reasons for it – cracks in the oil pan or even engine block as well as damages gasket. In these cases, you may easily find out leakage traces outside the engine or on the road under the car. If there are any you need urgent help from a professional car mechanic.

Noisy lifters and constant tapping sound from the engine valvetrain is a well-known symptom often named as “tappety engine”. It is the result of tappet plunger wear especially in case of low oil pressure and lack of lubrication over large mileage.
The protective layer created by the Atomium compound restores the shape of the plunger surface, optimizes the clearances, which prevents oil breakout and normalizes its pressure inside the mechanism. This ensures the normal work of the unit and stops tappet or lifter noise.
Note – Atomium compound is not a valve cleaning additive. Other products should be used to remove soot from the combustion chamber. 

There may be various reasons for a strange regular noise and vibrations of the engine. Not all of them may be fixed with an additive for engine noise. However, the most frequent cause is wear. It widens friction clearances which may lead to an iron “clunging” sound at engine start-up. It may lower compression in some cylinders, reduce the power of stroke and break the overall engine balance, so it starts to tremble. 
Restoring and equalizing the compression on the cylinders with the Atomium compound (as this was explained before) leads to the smooth operation of the engine. In addition, a thick and permanent oil film softens the contacts of metallic parts. All this allows to reduce or completely stop engine noise and vibrations.

The drop in oil pressure may be caused by an overall lack of oil in the system or by wear of the oil pump.
Restoring of the friction surfaces brings back outlet pressure of the pump to a nominal level and thus solves the problem. 

Restoring and equalization of compression provides better combustion of fuel. Thus less fuel is needed for the same amount of energy. 
Also, the dense oil film expands the hydrodynamic friction zone, which reduces friction losses by almost 50%. You may expect that engine treatment with the Atomium compound may reduce fuel consumption by 6-8% while you maintain your regular driving mode. The exact number depends on the initial state of your car and its mileage.
Note – Atomium compound is not a fuel additive, it doesn’t change fuel properties and neither changes combustion regimes. 

The normalization of compression provides a nominal power output of the engine. It is especially noticeable at acceleration when you need to raise up revs abruptly.
To get rid of the smoke from the exhaust, reduce its toxicity.
Recovery of compression and optimization of gaps in the cylinder-piston group ensures high-quality fuel combustion and reduce oil fumes. This reduces the content of unburned fuel particles and oil combustion products in the exhaust gases, which reduces their smoke and toxicity.

IN ADDITION TO THE SOLUTION OF ACTUAL PROBLEMS, THE USE OF TRIBO-COMPOUND ALLOWS YOU TO ACHIEVE PREVENTIVE EFFECTS:

The oil film retained by the protective layer on friction surfaces never flows down even during long idle periods. So the very first piston movements (as well as movements of other engine parts) at start up happen lubricated. It sufficiently reduces the wear of the engine. It is especially important in the cold weather when oil thickens in the pan and it takes more time to deliver it to the different engine sections.

Due to its structural features, the protective layer has increased microelasticity (it is deformed in a collision and then restores its shape instead of being destroyed) and microhardness (it requires more load to be destroyed). A denser oil film on the surface of the layer also reduces the direct contact of parts, withstands increased thermal and mechanical loads.
All this allows you to reduce engine wear. It is especially important for driving in traffic jams when the oil is overheated and liquefied due to the lack of cooling. And also at low speed maneuverштп when oil starvation occurs due to low pressure.

The oil film, held on the protective layer due to its structural features, is able to protect the engine from scuffing and jamming in the event of a sudden drop in oil pressure.
This allows you to avoid breakage if the oil loss or pressure drop was not noticed immediately. In addition, in some cases (depending on the design of the specific engine), this allows you to gently drive the car to the service station on your own.

SIGNS OF ENGINE WEAR

There are various signs of critical wear of engine components. As a rule, increasing wear is shown up by a decrease in engine dynamics, an increase of average fuel consumption in the same driving modes.
The following are some of the most common signs of wear and tear, in which the treatment of the engine with tribo-compound can significantly delay the need for repair:

There is a sound of "iron clang" when starting the engine

Due to wear of the cylinder walls, the gaps between them and the piston rings widen.
When starting the cold engine the gaps have not yet decreased due to the thermal expansion of the parts, the piston can make transverse movements accompanied by a shock. The rapid succession of blows merges into a general "ringing", the engine "rattles".
This is especially noticeable when starting in the cold weather when the gaps are widened even more. This indicates that the cylinder surfaces are very worn, and each such launch wears them even more.

There is constant blue smoke in the exhaust.

Blue smoke means that oil is constantly entering the combustion chambers, which indicates that there are widened gaps between cylinders and piston rings due to their wear.
Tribotechnical compound is able to restore worn surfaces, remove smoke, and reduce oil consumption. 

The engine started to work louder, harder, and there was a vibration.

These signs may indicate that the compression balance is disturbed.
Pistons in different cylinders are pushed with different forces, which disrupts the uniformity of the engine. If this sign appeared suddenly and sharply drew attention to itself, it is possible that there was a breakage – for example, a piston ring burst. If the vibration and noise increased gradually, imperceptibly, then most likely this is the result of wear. In this case, the Atomium tribotechnical compound will be able to restore the worn surfaces.

HOW DOES IT WORK?

Under the influence of tribo-compound, a protective metal layer is formed on the worn parts, which is able to retain a dense oil film permanently.
Restored shape and dimensions + denser oil film on the surface -> normal operation of the engine units.
The Tribotechnical compound contains particles of the active mineral.
Getting into the zones of local contacts of friction surfaces with a temperature of more than 1000 degrees and high pressure the mineral particles activate electronic connections in the metal. It allows the surface to capture the metal from the engine oil, which is there as a product of engine wear. Gradually, a special protective layer is formed on the entire friction surface. It is stronger than a normal surface and can hold denser oil film due to its porous structure.
The micropores of the protective layer are filled with oil, which forms a continuous film under surface tension forces. Restoring the shape and more effective lubrication, allow the parts to perform their functions as it was laid down in the engine design, which leads to the restoration of the performance characteristics of all friction units.

APPLICATION

EFFECTS OF APPLICATION

Oil additive to maintain performance characteristics and reduced wear of any type of engine after its complete treatment with other compounds of Active series. It should be added to motor oil after each (or at least each second) oil change. 
It restores protective layer on friction surfaces on the go and thus: significantly reduces wear speed, prolongs engine lifetime, maintain compression, highly efficient fuel burning and therefore power, acceleration and low fuel consumption. 
Active Regular designed to maintain protective layer, but isn’t able to restore a worn engine from the scratch. It is suitable for all engine types and designs, including turbocharged ones. It doesn’t change oil properties and acts only on metallic surfaces.

EFFECTS OF APPLICATION

Tribotechnical compounds of ACTIVE series create conditions under which the friction surfaces in engine parts are covered with a metallic protective layer, which has a special structure. This layer keeps more oil on the friction surfaces. Compound «Active Regular» provides support of this layer and its recovery in case of wear and tear, which in turn keeps the engine performance at the level reached at the processing engine with tribotechnical compounds of ACTIVE series.

It provides the following effects

INCREASING THE RESOURCE OF THE ENGINE OPERATION 

protective layer greatly reduces the wear of the most loaded friction parts, which determine engine life. Also, treated surfaces better hold oil, which protects the engine against oil starvation, during overheating, active driving and accidental loss of oil.

FACILITATING ENGINE START UP AND PROTECTION DURING «COLD START-UP» 

treated surfaces are able to retain the oil layer during the lengthy downtime of the engine. It facilitates the first shaft revolutions and prevents increased wear of engine with insufficient oil on friction surfaces at start-up, which is especially important at negative ambient temperature.

RATED MOTOR POWER

thick oil layer in clearances of the cylinder-piston group provides the necessary gas tightness, which leads to maintaining compression and quality combustion. Dense oil layer displaces the friction regime in the direction of the hydrodynamic, which reduces the friction losses. All this allows to keep the engine power at nominal values.

LOW FUEL CONSUMPTION

creating conditions for high-quality fuel combustion and reduction of friction losses provide fuel economy.

LOW OIL CONSUMPTION

keeping optimum clearance between the oil ring and cylinder wall prevents oil from entering the combustion chamber and allows to reduce or eliminate the oil burning.

LOW LEVEL OF NOISE AND VIBRATION

recovering of compression in the cylinders leads to smooth engine running. In addition, a dense layer of oil softens work of friction parts. Altogether, this reduces vibration and noise in the engine.

LOW TOXICITY

recovering of compression and optimization of gaps in the cylinder-piston group improves combustion quality, which in turn decreases exhaust CO/CH emissions.

APPLICATION

Instructions for application

Engine treatment is carried out after every regular oil change. It is necessary to add compound to new motor oil in accordance with the following procedure:

1. Warm up the engine to operating temperature (regular operation).
2. Stop the engine.
3. Stir Tribotechnical compound «Atomium Active Regular» thoroughly until natural sediments (active components) are totally dissolved.
4. Apply compound through the regular oil filling neck. Quantity the compound is determined according to the following scheme:

•  After applying the engine should run (it is recommended to drive the car) for no less than 20 - 25 min in of the regular operation mode.
• After the procedure, you can use the car as usual.

Engine oil additive (Tribotechnical compound) "Active STANDARD" is an additive in engine oil for the restoration of the piston group and other friction units.

The compound is intended for processing:

• automobile non-turbocharged gasoline engines with a volume of up to 1.6 liters. For engines with other characteristics, the composition "Active PLUS" is used;
• engines of 2-stroke motor vehicles: mopeds, trimmers, chainsaws, outboard motors, other tools and vehicles with two-stroke engines.

The composition restores the friction surfaces, protects them from wear, due to which:

• reduces oil burnings;
• eliminates bullies;
• increases power and acceleration;
• reduces exhaust smoke;
• restores and smoothes compression;
• reduces fuel consumption;
• extends engine life by 2-2.5 times;
• reduces the risk of bullying in case of emergency oil loss.
   

Tribotechnical compound does not react with motor oils and their packages of chemical additives, does not change their properties and characteristics, suitable for all types of motor oils.

EFFECTS OF APPLICATION

The tribotechnical compound - engine oil additive Atomium Active STANDARD is designed for thetreatment of non-powered gasoline engines with a working volume of less than 1.6 liters and an oil volume of less than 5 liters. Being in the engine oil, the composition creates conditions for the formation of a special protective layer of metal particles on the friction surfaces that appeared as a result of engine wear. This layer is stronger than a conventional surface and is able to hold a dense oil film due to its porous structure.

The stronger the friction, the higher the loads at local surface contacts, the more active the construction of a new layer is. With the gradual leveling of the surfaces and compaction of the oil film, the frequency and force of contact of the parts decreases, the formation of the layer stops.

The restoration of worn areas leads to the optimization of friction gaps, and the increased oil-holding capacity of the surface allows the engine oil to better cope with its functions.

In different parts of the engine, this leads to a number of positive changes in operation:

• The compression in the cylinders increases and levels out, which increases the completeness of fuel combustion and reduces its consumption, improves pick-up.
• The consumption of oil is reduced "on fumes", since its breakthrough into the combustion chamber is reduced.
• The oil pressure in the system is normalized by restoring the pump.
• The "clacking" of hydraulic compensators disappears.
• Noise and vibrations are reduced.
• The smokiness decreases when the engine is running.

Reducing friction facilitates the operation of the engine and significantly slows down further wear, which leads to an increase in the life of the unit by 2-2.5 times.

The ability of the protective layer to hold the oil film even with a long idle makes it easier to start the engine, especially in the cold, and also protects against wear when the oil overheats during long traffic jams.

In new cars, the composition accelerates the running-in of parts, reduces wear, which preserves the performance characteristics of the new engine for a long time.

APPLICATION

The tribotechnical compound - engine oil additive Atomium Active STANDARD is designed for thetreatment of non-powered gasoline engines with a working volume of less than 1.6 liters and an oil volume of less than 5 liters. Being in the engine oil, the composition creates conditions for the formation of a special protective layer of metal particles on the friction surfaces that appeared as a result of engine wear. This layer is stronger than a conventional surface and is able to hold a dense oil film due to its porous structure.

The stronger the friction, the higher the loads at local surface contacts, the more active the construction of a new layer is. With the gradual leveling of the surfaces and compaction of the oil film, the frequency and force of contact of the parts decreases, the formation of the layer stops.

The restoration of worn areas leads to the optimization of friction gaps, and the increased oil-holding capacity of the surface allows the engine oil to better cope with its functions.

In different parts of the engine, this leads to a number of positive changes in operation:

• The compression in the cylinders increases and levels out, which increases the completeness of fuel combustion and reduces its consumption, improves pick-up.
• The consumption of oil is reduced "on fumes", since its breakthrough into the combustion chamber is reduced.
• The oil pressure in the system is normalized by restoring the pump.
• The "clacking" of hydraulic compensators disappears.
• Noise and vibrations are reduced.
• The smokiness decreases when the engine is running.

Reducing friction facilitates the operation of the engine and significantly slows down further wear, which leads to an increase in the life of the unit by 2-2.5 times.

The ability of the protective layer to hold the oil film even with a long idle makes it easier to start the engine, especially in the cold, and also protects against wear when the oil overheats during long traffic jams.

In new cars, the composition accelerates the running-in of parts, reduces wear, which preserves the performance characteristics of the new engine for a long time.

Atomium AGSB restores worn out friction surfaces in various sections of a gearbox. A new metallic layer appears which is more hard and smooth than original surface. Also it is able to retain dense oil film. This improves operating of different mechanical systems. Particularly it allows to solve following tasks.

IN AUTOMATIC TRANSMISSIONS:

One of most often causes of shifting delays in automatic transmission is low oil pressure due to the wear of oil pump. To shift gears electronic controller sends a signal to valves in hydraulic block to close some of them and open others. Closing valves removes oil pressure from one friction pack and it gets released. At the same time oil comes through newly open valve and bring pressure to another clutch pack and lock it. If oil pressure is low locking of the second clutch happens with a little delay. For a split of second the torque is lost, car wheels slow down. When torque is caught back the speed of input shaft is faster than the output ones which gives feeling of unpleasant jerk or kick. 

Atomium transmission additive restores internal parts of oil pump, which helps it to provide nominal outlet pressure level. Clutches are locked in proper time which resolves the problem.

No matter at what gear shift the delay happens as it happens because of the same common reason. Restoration of the oil pump helps all of them to work correctly.

The metal protective layer created by Atomium AGSB restores the shape of the gear teeth. It ensures their correct and smooth engagement. A dense and permanent oil film retained by treated surfaces also makes the contact of teeth softer, decreases friction and wear. All this leads to a reduction in micro-impacts, ensures smooth interaction of the gears of the planetary transmission and thus reduces the noise and vibrations.

There is no matter at what exact shift the noise is most distinct and loud. All the gears are lubricated by the same all and Atomium AGSB will treat all of them. The only difference is that most worn out and consequently noisiest parts take longer to recover.

Atomium additive in the same way restores bearings races making them work quieter.

A dense oil film on the surfaces of the teeth ensures their smooth entry into and exit from the engagement, which reduces energy losses during transmission operation. This leads to a reduction in fuel consumption.

IN THE VARIATORS:

Restoring the geometry of the CVT cones, as well as retaining a denser layer of oil on the surface, can prevent chain slippage. It decrease jerks when picking up speed, makes acceleration stable and fast, sufficiently reduce speed of further cones wear.

It should be noted that the transmission oil used in continuously variable transmissions contains special additives that improve the grip of the chain and the surface of the cones. Thus, improving the performance of the lubricant does not weaken the friction between the chain and the cone, but on the contrary: the denser the oil film on the surfaces of the parts, the better the grip.

The protective layer on the surface of the cones has got higher microelasticity and microhardness. Therefore the surface of the cones treated with the compound is much less frayed during use, which prolongs the life of the unit.

HOW IT WORKS

Friction surfaces of metallic parts are not completely plain. On the microlevel there are micropeaks and hollows. When two surfaces rubbing each other they first contact by peaks in multiple points. In small area around such point there happens to be very high temperature and pressure.

Atomium AGSB contains special minerals. When they get into area with high temperature and pressure they get able to activate electronic links in the metallic surface. Thanks to that small particles of metal from the oil are getting attached to the surface. This process repeats in different points gradually creating a solid continuous protective layer all over the surface. The particles of the mineral itself remain in the oil and continue to affect the surface in other areas.

The protective layer is characterized by a porous structure with a large number of micro-hollows. They are filled with oil, which forms a continuous film on it due to surface tension forces. It is able to withstand increased loads on the breakdown, does not drain, even when the unit is idle for a long time. The protective layer itself wears out much slower than the original factory surface due to increased microhardness and microelasticity.

Optimized friction clearances and permanent dense oil film improve performance parameters of the treated mechanism.

HOW TO USE IT

Auto gearbox additive AGSB must be added once to the transmission oil through the standard oil filling hole. To continuously maintain the recovery effects it is recommended to add the compound with each regular oil change in the transmission.

APPLICATION

ATOMIUM APROHIM Car ventilation and air conditioner cleaner is a tool that destroys infectious contaminants in the car ventilation system: bacteria and fungi. It also contributes to the destruction of influenza viruses immediately after their appearance in the cabin. This eliminates unpleasant odors in the cabin, significantly reduces the risk of infectious diseases. This is described in more detail in the "Effects" tab.

There are some situations where cleaning the ventilation system is especially important:

• Sharing a car, if it is a company car or a taxi car;
• Trips with different people in the cabin during the off-season;
• Regular transportation of children in the car.
• Disinfection of the ventilation system with a cleaner can be easily carried out independently.
• It takes no more than 20 minutes.

EFFECTS OF APPLICATION

Effects of application

• reduction of fuel consumption by 5%-15% depending on the condition of the car.
• easier starting of the engine.
• extending the service life of fuel equipment, in particular injectors.
• reducing the load on the turbine, particulate filters, which extends their life.
• reduction of contaminants in engine oil, which maintains its performance properties and ultimately reduces engine wear.

Fuel additive ATOMIUM APROHIM SGA gently cleans fuel systems, lubricates them, protects against corrosion and prevents the formation of deposits. This restores the performance of fuel pumps, injectors or injectors, protects them from wear and extends their service life. A comprehensive restoration of the fuel equipment improves injection, leads to a decrease in fuel consumption and an increase in dynamics.

Effects of Application

Pollution from inferior fuel is the main cause of performance degradation and fuel system failure. Fuel additive SGA imparts cleaning and lubricating properties to gasoline fuel, blocks corrosion of system elements due to the ingress of water or condensate.

Cleaning the pumps and reducing piston wear normalizes the fuel pressure in the system. Cleaning of valves, channels and jet nozzles - prolongs their service life. Together, this ensures quality fuel atomization and more complete combustion, resulting in the following effects:

•     Reduction in fuel consumption by 5%-15% depending on the condition of the car.
•     Extending the life of fuel systems.
  
•     Reducing vibrations by evenly burning fuel in the cylinders.
•     Reducing the load on the turbine, catalytic converters, fuel afterburners, thereby increasing their service life.
•     Reduction of contaminants in engine oil, maintaining its performance characteristics and ultimately reducing engine wear.
  
  The additive SGA is designed for long-term use, so it has a balanced "soft" formulation. It gradually removes dirt and deposits and prevents the formation of new ones. The additive does not contain "combustion promoters" or other substances that alter the way the engine operates.
  
  The additive is sold in disposable bottles - in most cases one bottle for each filling of a full tank.
  

Appliction mode:

• shake the contents of the bottle thoroughly;
• open the bottle and pour the additive into the fuel tank (use the fuel funnel if necessary);
• fill the car with fuel.
• When the car has run more than 50,000 kilometres during the first two refuelling it is recommended to fill 2 bottles of product 50 ml per 40-60 litres of fuel (or at the rate of 2 ml per 1 litre of fuel).

Designed for application on High-pressure fuel pumps (HPFP), Common rail systems, Pump injectors of diesel engines.

FEATURES

Lubricant Composition Atomium  HPFP is designed for the treatment of High-pressure fuel pumps (HPFP), Common rail systems, Pump injectors of diesel engines.

The treatment to be made in 2 stages.

For the treatment use calculation in running hours (moto-hours): for generators and other stationary equipment 1 running hour = 50 km of run, for wheel tractors (and equipment) 1 running hour = 10 km of run, for a caterpillar special equipment 1 running hour = 5 km of run.

Precautions: Not harmful if applied correctly.

First aid:

• In case of contact with skin remove the material wash out with warm water, and then wash again with soap.
• In case of contact with eyes wash out eyes with a large amount of water.
• In case of swallowing consult a doctor.

APPLICATION MODE

The 1st stage: Pour Lubricant Composition Atomium  HPFP in a full fuel tank (but no more than 50-55 liters of diesel fuel in a tank) at the rate of 1 ml of the lubricant on 1 L of diesel fuel. Drive till complete fuel depletion in the fuel reservoir (before the indicator shows the minimum fuel rest). Make refueling without adding Atomium  HPFP, then run 2000-3000 km till the 2nd stage.

The 2nd stage: Pour Atomium  HPFP in a full fuel tank (but no more than 50-55 liters of diesel fuel in a tank) at the rate of 1 ml of Suprotec on 1 L of diesel fuel. Drive till complete fuel depletion in the fuel reservoir (before the indicator shows the minimum fuel rest). Then make regular refueling.

Important notes:

• Before applying Atomium  HPFP shake the can thoroughly until natural sediments (active components) are totally dissolved.
• After applying Atomium  HPFP drive the vehicle for no less than 20 minutes in any mode (regular operation).
• It is recommended to carry out Atomium treatment of the fuel systems together with engine processing at the same time or sequentially.
• It is not recommended to apply the lubricant at the existence of mechanical breakages of diesel injectors (the belts of injectors cannot be restored).
• Atomium  HPFP is compatible with any type of diesel fuel.
• To provide an optimal level of technical condition of the fuel system it is recommended to apply Atomium  HPFP every 30 000 - 40 000 km of run.

EFFECTS OF APPLICATION

• Restores working parameters (pressure) of high-pressure fuel pumps, Common rail systems, Pump injectors of diesel engines (as a result of optimization of spacings in conjugated friction parts);
• Significantly decreases noise and vibration levels in HPFP;
• Increases of a lifetime of the HPFP, Common rail systems, Pump injectors in 1.5 – 2 times (due to wear intensity decreasing);
• Increases engine effective power (as a result of fuel combustion quality improvement,);
• Decreases fuel consumption by 3-5 % (as a result of compression recovering and combustion quality improvement);
• Decreases exhaust CO/CH emissions up to 50 % (as a result of improvement of combustion quality)

The composition is designed to restore performance and extend the life of the power steering of cars. Extends the life of the hydraulic booster. Restoration of worn parts, protection against wear under increased loads and high ambient temperatures extends the life of the unit by 1.5-2 times.

Effects of application

Being in transmission oil, the composition of the "Power Steering" creates conditions under which a metal protective layer is formed on the friction surfaces. This layer partially restores worn parts of the hydraulic booster pump, optimizes the gaps, allows you to keep a denser oil layer on their surface, and cleans the spool mechanism.

This allows you to normalize the operation of the unit, restore the pressure of the pump, which leads to a number of positive effects:

• The steering wheel is easier to turn. Normalization of the pump operation gives an increase in pressure up to three kilograms, which greatly facilitates turning the steering wheel;
• Reduces noise and vibration. Restoration of the hydraulic booster pump, cleaning of bypass valves reduce noise and vibration during the operation of the hydraulic booster;
• Extends the life of the hydraulic booster. Restoration of worn parts, protection against wear under increased loads and high ambient temperatures extends the life of the unit by 1.5-2 times.

The pump of HPS system should be treated in 2 stages.

The 1st stage:

• Before applying shake the can with compound thoroughly until all the sediments (active components) are totally dissolved.
• Pour half of Atomium HPS through the regular filling neck of the hydraulic power steering (30 ml for 1 liter of hydraulic fluid to be exact).
  
• Start the engine and make 10-15 left-right turns of stirring wheel to maximum degree.
  
• Drive in your normal regime for 15-20 minutes.
  
• Then drive about 1500-2000 kilometers.

The 2nd stage:

It is recommended to change hydraulic fluid and filters (if there are any) after about 2000 km. However it is not obligatory if there are no complaints about the mechanism. In case of fluid replacement – add another half of compound (another 30 ml per 1 liter) following instructions above.

Precautions:

Not harmful if applied correctly.

First aid:

• In case of a contact with skin remove the material wash out with warm water, and then wash again with soap;
• In case of contact with eyes wash out eyes with large amount of water;
  
• In case of swallowing consult a doctor.

The additive is designed for application on High-pressure fuel pumps (HPFP), Common rail systems, Pump injectors of diesel engines.

FEATURES

Lubricant Composition Atomium Max  HPFP is designed for the treatment of High-pressure fuel pumps (HPFP), Common rail systems, Pump injectors of diesel engines

The treatment to be made in 2 stages.

Mode of application: add  to the diesel fuel to the fuel tank

For treatment use calculation in running hours (moto-hours): for generators and other stationary equipment 1 running hour = 50 km of run, for wheel tractors (and equipment) 1 running hour = 10 km of run, for a caterpillar special equipment 1 running hour = 5 km of run.

Precautions: Not harmful if applied correctly.

First aid:

• In case of contact with skin remove the material wash out with warm water, and then wash again with soap.
• In case of contact with eyes wash out eyes with a large amount of water.
• In case of swallowing consult a doctor.

APPLICATION MODE

The 1st stage: Pour Lubricant Composition Atomium Max  HPFP in a full fuel tank (but no more than 200-220 liters of diesel fuel in a tank) at the rate of 1 ml of the lubricant on 1 L of diesel fuel. Drive till complete fuel depletion in the fuel reservoir (before the indicator shows the minimum fuel rest). Make refueling without adding Atomium Max  HPFP, then run 2000-3000 km till the 2nd stage.

The 2nd stage: Pour Atomium Max  HPFP in a full fuel tank (but no more than 200-220 liters of diesel fuel in a tank) at the rate of 1 ml of Atomium on 1 L of diesel fuel. Drive till complete fuel depletion in the fuel reservoir (before the indicator shows the minimum fuel rest). Then make regular refueling.

Important notes:

• Before applying Atomium Max  HPFP shake the can thoroughly until natural sediments (active components) are totally dissolved.
• After applying Atomium Max HPFP drive the vehicle for no less than 20 minutes in any mode (regular operation).
• It is recommended to carry out Atomium treatment of the fuel systems together with engine processing at the same time or sequentially.
• It is not recommended to apply the lubricant at the existence of mechanical breakages of diesel injectors (the belts of injectors cannot be restored).
• Atomium MaxHPFP is compatible with any type of diesel fuel.
• To provide an optimal level of technical condition of the fuel system it is recommended to apply Atomium Max HPFP every 100 000 - 300 000 km of run.

EFFECTS OF APPLICATION

• Restores working parameters (pressure) of high-pressure fuel pumps, Common rail systems, Pump injectors of diesel engines (as a result of optimization of spacings in conjugated friction parts);
• Significantly decreases noise and vibration levels in HPFP;
• Increases of a lifetime of the HPFP, Common rail systems, Pump injectors in 1.5 – 2 times (due to wear intensity decreasing);
• Increases engine effective power (as a result of fuel combustion quality improvement,);
• Decreases fuel consumption by 3-5 % (as a result of compression recovering and combustion quality improvement);
• Decreases exhaust CO/CH emissions up to 50 % (as a result of improvement of combustion quality)

The additive is designed for application on mechanical gearboxes, rear axles, and reduction gears of any type.

FEATURES

Lubricant Composition Atomium Max MGSB   is designed for the treatment of mechanical gearboxes, rear axles, reduction gears of any type, and self-locking differentials. 
The treatment to be made in one stage.

Mode of application: add  to the transmission oil

Precautions: Not harmful if applied correctly.

First aid:

• In case of contact with skin remove the material wash out with warm water, and then wash again with soap.
• In case of contact with eyes wash out eyes with a large amount of water.
• In case of swallowing consult a doctor.

APPLICATION MODE

Add Lubricant Composition Atomium  MAX  MGSB to the working oil in the unit at the rate of 10-15 ml of the Lubricant per 1 liter of transmission oil. 
After applying Atomium MAX MGSB drive the car in a regular mode for no less than 20 minutes. Run till the next regular oil replacement (but no less than 2000 km).

Important notes:

• Before applying ATOMIUM MAX MGSB shake the can thoroughly until natural sediments (active components) are totally dissolved.
• Apply ATOMIUM MAX  MGSB through the regular filling neck of the warmed-up unit.
• After applying ATOMIUM MAX  MGSB drive the car for no less than 20 minutes in any mode (regular operation).
• It is recommended to carry out Atomium treatment of mechanical transmissions together with engine processing at the same time or sequentially.
• It is not recommended to apply the lubricant to the existence of mechanical breakages of parts and assemblies.
• ATOMIUM MAX   MGSB is compatible with any type of transmission oil and doesn't change its properties (apart from ATF Synthetic Automatic Transmission Fluid).
• To provide a continuous level of protection of the unit it is recommended to apply LC further after each oil change (every 50 000 – 70 000 km).

EFFECTS OF APPLICATION

• Improves the process of burnishing the unit parts, including condition after overhaul (because of the adaptive properties of the LC, that work on optimization of conjugated friction parts);
• Increases the unit lifetime in 1,5-2 times (due to wear intensity decreasing);
• Decreases friction losses in unit details (as a result of improvement of the friction mode);
• Provides maximum protection of the unit against wear in case of overloading or overheating under high temperature of the environment;
• Doesn't worsen the operational characteristics of rubber parts;
• Significantly reduces noise and vibration levels in the gearbox, rear axle (due to forming of thick and resistant lubrication “pillow” and clearances optimization);
• Restores optimum spacings in bearings and serrated gearings;
• Restores the ease of gearshift due to the recovery of gaps and reduction of friction losses;
• Provides the possibility of short-time run under oil starvation conditions in the unit.

ATOMIUM MAX 200 ENGINE - engine oil Additive for trucks and light commercial vehicles engines to protect against wear, extend the service life and restore the characteristics of diesel engines of trucks with a working volume of more than 5 liters

EFFECTS OF APPLICATION

Additive MAX 200 HPFP  is designed to restore performance and extend the life of high pressure fuel pumps diesel engines trucks and special equipment:

• inline fuel pumps;
• fuel distribution pumps;
• mainline fuel pumps in COMMON RAIL systems;
• systems "PUMP-NOZZLE".

EFFECTS OF APPLICATION

Hydraulic fluid additive (compound) "MAX HYDRAULIC" creates conditions under which a protective metal layer with a special structure appears on the friction surfaces.

EFFECTS OF APPLICATION

ATOMIUM MAX 200 MGSB - gearbox oil additive for trucks and light commercial vehicles to protect against wear, extend the service life and restore the characteristics of gearboxes, transfer boxes and gearboxes of trucks and special equipment

EFFECTS OF APPLICATION

EFFECTS OF APPLICATION

EFFECTS OF APPLICATION

Tribotechnical compound «MOTOTEC 2" produced by ATOMIUM is designed to restore the performance and protect against wearing the two-stroke engines of mopeds, all-terrain vehicles (quad bikes), and other motor vehicles, including engines with separate lubrication system.

Instructions

Compound "MOTOTEС 2" is added to the working oil of the engine by the following procedure:

1. Warm up the engine to operating temperature
2. Stop the engine
3. Shake the can thoroughly until natural sediments (active components) are totally dissolved.
4. Add the compound to the engine through its regular oil filling neck.

Apply the half can only –  if the engine has a separate lubrication system.  Apply the compound at the rate of 5 ml of compound per 1 liter of oil – if the engine has a common lubrication system.

Start the engine and take a trip lasting 15-20 minutes in normal driving mode at once after the procedure.

Full engine treatment is performed as follows:

Effects of application 

• Increases power
• Decreases vibration and noise level
• Increases  engine lifetime

Tribotechnical compound «Reducer» is designed to protect against wear, increase the lifetime and restore characteristics of transfer boxes, limited-slip differentials.

FEATURES

Lubricant Composition Atomium Reducer 80 is designed for the treatment of mechanical against wear, increase the lifetime, and restore characteristics of transfer boxes, limited-slip differentials, viscous couplings, haldex clutches, increased friction reducers, and other reducers which use any type of transmission fluid.

Precautions: Not harmful if applied correctly.

First aid:

• In case of contact with skin remove the material wash out with warm water, and then wash again with soap.
• In case of contact with eyes wash out eyes with a large amount of water.
• In case of swallowing consult a doctor.

APPLICATION MODE

Treatment of transfer cases, differentials, and other reducers is made in accordance with the following procedure:

• Warm up the unit to operating temperature (regular operation). It takes usually 15-20 minutes of unit operation under load.
• Stop the engine
• Shake the can thoroughly until natural sediments (active components) are totally dissolved.
• Apply 1 can of the compound through the unit’s regular filling neck. 1 can is enough for treatment of the unit with transmission fluid volume from 0.7 to 2.2 liters.
• It is recommended to drive the car for no less than 25 - 30 min. in the mode of regular operation after applying.

After the procedure, you can use the car as usual.

To provide a continuous level of protection of the unit it is recommended to apply the compound further after each scheduled replacement of transmission fluid.

EFFECTS OF APPLICATION

• Improves the process of burnishing the unit parts, including condition after overhaul (because of the adaptive properties of the LC, that work on optimization of conjugated friction parts);
• Increases the unit lifetime in 1,5-2 times (due to wear intensity decreasing);
• Decreases friction losses in unit details (as a result of improvement of the friction mode);
• Provides maximum protection of the unit against wear in case of overloading or overheating under high temperature of the environment;
• Doesn't worsen the operational characteristics of rubber parts;
• Significantly reduces noise and vibration levels in the gearbox, rear axle (due to forming of thick and resistant lubrication “pillow” and clearances optimization);
• Restores optimum spacings in bearings and serrated gearings;
• Doesn't change parameters and technical characteristics of knots of the clutch in the oil bathtub;
• Provides the possibility of short-time run under oil starvation conditions in the unit.